1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
|
#
# Use this file as a starting point for your custom gumstix configuration
# Edit it to reflect your hardware setup and then save it a parallel location in user.collection
MACHINE_FEATURES += "connex"
require conf/machine/include/gumstix.inc
#
# Your flash size = Total flash (in MB) - 1 (for linux kernel partition)
#ROOT_FLASH_SIZE = "3"
ROOT_FLASH_SIZE = "15"
#
# Enable use of virtual terminal for LCD on tty1 if USE_VT = "1"
USE_VT = "0"
#USE_VT = "1"
#SYSVINIT_ENABLED_GETTYS = "1"
#
# Uncomment features that your board set supports
#MACHINE_FEATURES += "usbhost"
MACHINE_FEATURES += "usbgadget"
MACHINE_FEATURES += "i2c"
#MACHINE_FEATURES += "spi"
MACHINE_FEATURES += "serial"
MACHINE_FEATURES += "bluetooth"
MACHINE_FEATURES += "sound"
# if you enable robostix you will need to disable both "lcd" and "touchscreen" features
#MACHINE_FEATURES += "robostix"
MACHINE_FEATURES += "lcd"
MACHINE_FEATURES += "rgb16"
#MACHINE_FEATURES += "rgb18"
MACHINE_FEATURES += "touchscreen"
#MACHINE_FEATURES += "keyboard"
MACHINE_FEATURES += "pcmcia"
#MACHINE_FEATURES += "mmc"
MACHINE_FEATURES += "wifi"
MACHINE_FEATURES += "ethernet"
MACHINE_FEATURES += "fat"
MACHINE_FEATURES += "ext2"
# enable one of the following if you want to target build for uimage/rootfs on mmc/microSD or CF
#MACHINE_FEATURES += "mmcroot"
#MACHINE_FEATURES += "cfroot"
#
# note: selection of MACHINE_FEATURES above will automatically include necessary kernel modules
# for those features via task-base-gumstix. Include below any extra kernel modules that you want installed
#MACHINE_ESSENTIAL_EXTRA_RRECOMMENDS += "kernel-module-xxxxxxx"
#
# Uncomment or add kernel modules that should be autoloaded
module_autoload_proc_gpio = 'proc_gpio'
module_autoload_pcmcia = ${@base_contains('MACHINE_FEATURES', 'pcmcia', 'pcmcia', '',d)}
module_autoload_pxa2xx_cs = ${@base_contains('MACHINE_FEATURES', 'pcmcia', 'pxa2xx_cs', '',d)}
module_autoload_pxamci = ${@base_contains('MACHINE_FEATURES', 'mmc', 'pxamci', '',d)}
module_autoload_mmc_block = ${@base_contains('MACHINE_FEATURES', 'mmc', 'mmc_block', '',d)}
module_autoload_ethernet = ${@base_contains('MACHINE_FEATURES', 'ethernet', 'ethernet', '',d)}
module_autoload_gumstix_gadget = ${@base_contains('MACHINE_FEATURES', 'usbgadget', 'gumstix_gadget', '',d)}
#module_autoload_g_file_storage = ${@base_contains('MACHINE_FEATURES', 'usbgadget', 'g_file_storage', '',d)}
module_autoload_g_ether = ${@base_contains('MACHINE_FEATURES', 'usbgadget', 'g_ether', '',d)}
#module_autoload_g_serial = ${@base_contains('MACHINE_FEATURES', 'usbgadget', 'g_serial', '',d)}
module_autoload_tsc2003 = ${@base_contains('MACHINE_FEATURES', 'touchscreen','tsc2003', '',d)}
module_autoload_ucb1400-ts = ${@base_contains('MACHINE_FEATURES', 'touchscreen','ucb1400-ts', '',d)}
module_autoload_evdev = ${@base_contains('MACHINE_FEATURES', 'touchscreen','evdev', '',d)}
|
