diff options
Diffstat (limited to 'documentation/dev-manual')
-rw-r--r-- | documentation/dev-manual/dev-manual-common-tasks.xml | 26 |
1 files changed, 13 insertions, 13 deletions
diff --git a/documentation/dev-manual/dev-manual-common-tasks.xml b/documentation/dev-manual/dev-manual-common-tasks.xml index 48d3ecb632..bd11062c41 100644 --- a/documentation/dev-manual/dev-manual-common-tasks.xml +++ b/documentation/dev-manual/dev-manual-common-tasks.xml @@ -8777,19 +8777,19 @@ within a separately started QEMU or any other virtual machine manager. </para></listitem> - <listitem><para><emphasis>"GummibootTarget":</emphasis> - Choose "GummibootTarget" if your hardware is + <listitem><para><emphasis>"Systemd-bootTarget":</emphasis> + Choose "Systemd-bootTarget" if your hardware is an EFI-based machine with - <filename>gummiboot</filename> as bootloader and + <filename>systemd-boot</filename> as bootloader and <filename>core-image-testmaster</filename> (or something similar) is installed. Also, your hardware under test must be in a DHCP-enabled network that gives it the same IP address for each reboot.</para> - <para>If you choose "GummibootTarget", there are + <para>If you choose "Systemd-bootTarget", there are additional requirements and considerations. See the - "<link linkend='selecting-gummiboottarget'>Selecting GummibootTarget</link>" + "<link linkend='selecting-systemd-boottarget'>Selecting Systemd-bootTarget</link>" section, which follows, for more information. </para></listitem> <listitem><para><emphasis>"BeagleBoneTarget":</emphasis> @@ -8835,12 +8835,12 @@ </para> </section> - <section id='selecting-gummiboottarget'> - <title>Selecting GummibootTarget</title> + <section id='selecting-systemd-boottarget'> + <title>Selecting Systemd-bootTarget</title> <para> If you did not set <filename>TEST_TARGET</filename> to - "GummibootTarget", then you do not need any information + "Systemd-bootTarget", then you do not need any information in this section. You can skip down to the "<link linkend='qemu-image-running-tests'>Running Tests</link>" @@ -8849,14 +8849,14 @@ <para> If you did set <filename>TEST_TARGET</filename> to - "GummibootTarget", you also need to perform a one-time + "Systemd-bootTarget", you also need to perform a one-time setup of your master image by doing the following: <orderedlist> <listitem><para><emphasis>Set <filename>EFI_PROVIDER</filename>:</emphasis> Be sure that <filename>EFI_PROVIDER</filename> is as follows: <literallayout class='monospaced'> - EFI_PROVIDER = "gummiboot" + EFI_PROVIDER = "systemd-boot" </literallayout> </para></listitem> <listitem><para><emphasis>Build the master image:</emphasis> @@ -8920,7 +8920,7 @@ <para> The final thing you need to do when setting - <filename>TEST_TARGET</filename> to "GummibootTarget" is + <filename>TEST_TARGET</filename> to "Systemd-bootTarget" is to set up the test image: <orderedlist> <listitem><para><emphasis>Set up your <filename>local.conf</filename> file:</emphasis> @@ -8929,7 +8929,7 @@ <literallayout class='monospaced'> IMAGE_FSTYPES += "tar.gz" INHERIT += "testimage" - TEST_TARGET = "GummibootTarget" + TEST_TARGET = "Systemd-bootTarget" TEST_TARGET_IP = "192.168.2.3" </literallayout> </para></listitem> @@ -9325,7 +9325,7 @@ The target controller object used to deploy and start an image on a particular target (e.g. QemuTarget, SimpleRemote, and - GummibootTarget). + Systemd-bootTarget). Tests usually use the following: <itemizedlist> <listitem><para><emphasis><filename>ip</filename>:</emphasis> |