# This is an example configuration file for the LVM2 system. # It contains the default settings that would be used if there was no # /etc/lvm/lvm.conf file. # # Refer to 'man lvm.conf' for further information including the file layout. # # To put this file in a different directory and override /etc/lvm set # the environment variable LVM_SYSTEM_DIR before running the tools. # This section allows you to configure which block devices should # be used by the LVM system. devices { # Where do you want your volume groups to appear ? dir = "/dev" # An array of directories that contain the device nodes you wish # to use with LVM2. scan = [ "/dev" ] # A filter that tells LVM2 to only use a restricted set of devices. # The filter consists of an array of regular expressions. These # expressions can be delimited by a character of your choice, and # prefixed with either an 'a' (for accept) or 'r' (for reject). # The first expression found to match a device name determines if # the device will be accepted or rejected (ignored). Devices that # don't match any patterns are accepted. # Be careful if there there are symbolic links or multiple filesystem # entries for the same device as each name is checked separately against # the list of patterns. The effect is that if any name matches any 'a' # pattern, the device is accepted; otherwise if any name matches any 'r' # pattern it is rejected; otherwise it is accepted. # Don't have more than one filter line active at once: only one gets used. # Run vgscan after you change this parameter to ensure that # the cache file gets regenerated (see below). # If it doesn't do what you expect, check the output of 'vgscan -vvvv'. # By default we accept every block device: filter = [ "a/.*/" ] # Exclude the cdrom drive # filter = [ "r|/dev/cdrom|" ] # When testing I like to work with just loopback devices: # filter = [ "a/loop/", "r/.*/" ] # Or maybe all loops and ide drives except hdc: # filter =[ "a|loop|", "r|/dev/hdc|", "a|/dev/ide|", "r|.*|" ] # Use anchors if you want to be really specific # filter = [ "a|^/dev/hda8$|", "r/.*/" ] # The results of the filtering are cached on disk to avoid # rescanning dud devices (which can take a very long time). By # default this cache file is hidden in the /etc/lvm directory. # It is safe to delete this file: the tools regenerate it. cache = "/etc/lvm/.cache" # You can turn off writing this cache file by setting this to 0. write_cache_state = 1 # Advanced settings. # List of pairs of additional acceptable block device types found # in /proc/devices with maximum (non-zero) number of partitions. # types = [ "fd", 16 ] # If sysfs is mounted (2.6 kernels) restrict device scanning to # the block devices it believes are valid. # 1 enables; 0 disables. sysfs_scan = 1 # By default, LVM2 will ignore devices used as components of # software RAID (md) devices by looking for md superblocks. # 1 enables; 0 disables. md_component_detection = 1 } # This section that allows you to configure the nature of the # information that LVM2 reports. log { # Controls the messages sent to stdout or stderr. # There are three levels of verbosity, 3 being the most verbose. verbose = 0 # Should we send log messages through syslog? # 1 is yes; 0 is no. syslog = 1 # Should we log error and debug messages to a file? # By default there is no log file. #file = "/var/log/lvm2.log" # Should we overwrite the log file each time the program is run? # By default we append. overwrite = 0 # What level of log messages should we send to the log file and/or syslog? # There are 6 syslog-like log levels currently in use - 2 to 7 inclusive. # 7 is the most verbose (LOG_DEBUG). level = 0 # Format of output messages # Whether or not (1 or 0) to indent messages according to their severity indent = 1 # Whether or not (1 or 0) to display the command name on each line output command_names = 0 # A prefix to use before the message text (but after the command name, # if selected). Default is two spaces, so you can see/grep the severity # of each message. prefix = " " # To make the messages look similar to the original LVM tools use: # indent = 0 # command_names = 1 # prefix = " -- " # Set this if you want log messages during activation. # Don't use this in low memory situations (can deadlock). # activation = 0 } # Configuration of metadata backups and archiving. In LVM2 when we # talk about a 'backup' we mean making a copy of the metadata for the # *current* system. The 'archive' contains old metadata configurations. # Backups are stored in a human readeable text format. backup { # Should we maintain a backup of the current metadata configuration ? # Use 1 for Yes; 0 for No. # Think very hard before turning this off! backup = 1 # Where shall we keep it ? # Remember to back up this directory regularly! backup_dir = "/etc/lvm/backup" # Should we maintain an archive of old metadata configurations. # Use 1 for Yes; 0 for No. # On by default. Think very hard before turning this off. archive = 1 # Where should archived files go ? # Remember to back up this directory regularly! archive_dir = "/etc/lvm/archive" # What is the minimum number of archive files you wish to keep ? retain_min = 10 # What is the minimum time you wish to keep an archive file for ? retain_days = 30 } # Settings for the running LVM2 in shell (readline) mode. shell { # Number of lines of history to store in ~/.lvm_history history_size = 100 } # Miscellaneous global LVM2 settings global { # The file creation mask for any files and directories created. # Interpreted as octal if the first digit is zero. umask = 077 # Allow other users to read the files #umask = 022 # Enabling test mode means that no changes to the on disk metadata # will be made. Equivalent to having the -t option on every # command. Defaults to off. test = 0 # Whether or not to communicate with the kernel device-mapper. # Set to 0 if you want to use the tools to manipulate LVM metadata # without activating any logical volumes. # If the device-mapper kernel driver is not present in your kernel # setting this to 0 should suppress the error messages. activation = 1 # If we can't communicate with device-mapper, should we try running # the LVM1 tools? # This option only applies to 2.4 kernels and is provided to help you # switch between device-mapper kernels and LVM1 kernels. # The LVM1 tools need to be installed with .lvm1 suffices # e.g. vgscan.lvm1 and they will stop working after you start using # the new lvm2 on-disk metadata format. # The default value is set when the tools are built. # fallback_to_lvm1 = 0 # The default metadata format that commands should use - "lvm1" or "lvm2". # The command line override is -M1 or -M2. # Defaults to "lvm1" if compiled in, else "lvm2". # format = "lvm1" # Location of proc filesystem proc = "/proc" # Type of locking to use. Defaults to file-based locking (1). # Turn locking off by setting to 0 (dangerous: risks metadata corruption # if LVM2 commands get run concurrently). locking_type = 1 # Local non-LV directory that holds file-based locks while commands are # in progress. A directory like /tmp that may get wiped on reboot is OK. locking_dir = "/tmp/lock/lvm" # Other entries can go here to allow you to load shared libraries # e.g. if support for LVM1 metadata was compiled as a shared library use # format_libraries = "liblvm2format1.so" # Full pathnames can be given. # Search this directory first for shared libraries. # library_dir = "/lib" } activation { # Device used in place of missing stripes if activating incomplete volume. # For now, you need to set this up yourself first (e.g. with 'dmsetup') # For example, you could make it return I/O errors using the 'error' # target or make it return zeros. missing_stripe_filler = "/dev/ioerror" # Size (in KB) of each copy operation when mirroring mirror_region_size = 512 # How much stack (in KB) to reserve for use while devices suspended reserved_stack = 256 # How much memory (in KB) to reserve for use while devices suspended reserved_memory = 8192 # Nice value used while devices suspended process_priority = -18 # If volume_list is defined, each LV is only activated if there is a # match against the list. # "vgname" and "vgname/lvname" are matched exactly. # "@tag" matches any tag set in the LV or VG. # "@*" matches if any tag defined on the host is also set in the LV or VG # # volume_list = [ "vg1", "vg2/lvol1", "@tag1", "@*" ] } #################### # Advanced section # #################### # Metadata settings # # metadata { # Default number of copies of metadata to hold on each PV. 0, 1 or 2. # You might want to override it from the command line with 0 # when running pvcreate on new PVs which are to be added to large VGs. # pvmetadatacopies = 1 # Approximate default size of on-disk metadata areas in sectors. # You should increase this if you have large volume groups or # you want to retain a large on-disk history of your metadata changes. # pvmetadatasize = 255 # List of directories holding live copies of text format metadata. # These directories must not be on logical volumes! # It's possible to use LVM2 with a couple of directories here, # preferably on different (non-LV) filesystems, and with no other # on-disk metadata (pvmetadatacopies = 0). Or this can be in # addition to on-disk metadata areas. # The feature was originally added to simplify testing and is not # supported under low memory situations - the machine could lock up. # # Never edit any files in these directories by hand unless you # you are absolutely sure you know what you are doing! Use # the supplied toolset to make changes (e.g. vgcfgrestore). # dirs = [ "/etc/lvm/metadata", "/mnt/disk2/lvm/metadata2" ] #} # Event daemon # dmeventd { # mirror_library is the library used when monitoring a mirror device. # # "libdevmapper-event-lvm2mirror.so" attempts to recover from # failures. It removes failed devices from a volume group and # reconfigures a mirror as necessary. If no mirror library is # provided, mirrors are not monitored through dmeventd. mirror_library = "@libdir@/device-mapper/libdevmapper-event-lvm2mirror.so" # snapshot_library is the library used when monitoring a snapshot device. # # "libdevmapper-event-lvm2snapshot.so" monitors the filling of # snapshots and emits a warning through syslog when the use of # the snapshot exceeds 80%. The warning is repeated when 85%, 90% and # 95% of the snapshot is filled. snapshot_library = "@libdir@/device-mapper/libdevmapper-event-lvm2snapshot.so" # thin_library is the library used when monitoring a thin device. # # "libdevmapper-event-lvm2thin.so" monitors the filling of # pool and emits a warning through syslog when the use of # the pool exceeds 80%. The warning is repeated when 85%, 90% and # 95% of the pool is filled. thin_library = "@libdir@/device-mapper/libdevmapper-event-lvm2thin.so" # Full path of the dmeventd binary. # # executable = "@DMEVENTD_PATH@" }