| Age | Commit message (Collapse) | Author |
|---|
|
When systemd is used, it will invoke a service on first boot that triggers
a rebuild of ldconfig caches (rebuild dynamic linker cache).
This is fine on the first boot of a system that has been installed, but it
makes no sense on a live system. The worst part is that rebuilding this
caches is slow and it causes the live system to take longer to boot.
(I measured this in 30 seconds longer on a standard PC system booting
core-image-sato live from an USB memory).
Disable this by touching /etc/.updated and /var/.updated on the live initramfs.
For more details see https://bugzilla.redhat.com/show_bug.cgi?id=1201725 and
https://www.freedesktop.org/software/systemd/man/systemd-update-done.service.html
Signed-off-by: Carlos Alberto Lopez Perez <clopez@igalia.com>
Signed-off-by: Ross Burton <ross.burton@intel.com>
|
|
After systemd-boot was introduced, its been tested for a while with no major
issues being found until now, this patch completely replaces all gummiboot
instances with systemd-boot ones, taking the next step into cleaning
up systemd-boot/gummiboot.
[YOCTO #10332]
Signed-off-by: Alejandro Hernandez <alejandro.hernandez@linux.intel.com>
Signed-off-by: Ross Burton <ross.burton@intel.com>
|
|
Add awareness of /dev/nvme* block devices to install scripts. As presently
written, installer knows only of /dev/sd* and /dev/mmcblk* block devices.
Building upon scaffolding put in place by Awais in...
80ec9f627915 ("initrdscripts: handle mmc device as installer medium")
Signed-off-by: Joe Konno <joe.konno@intel.com>
Signed-off-by: Ross Burton <ross.burton@intel.com>
|
|
devices
The init-install.sh and init-install-efi.sh scripts perform a check
to see which devices are available on a booted system for installation.
Recently, the way we check for these devices changed on 993bfb,
greping for devices found on /sys/block/, this change caused the installer
to fail (at least) when not finding any mmcblk devices, due to the fact
that we call sh -e to execute this script, so any command (grep)
or pipeline exiting with a non-zero status causes the whole script to exit
This patch throws in a harmless true exit status at the end of the pipeline(s)
of the grep commands to avoid the installer script from exiting, fixing the issue.
[YOCTO #10189]
Signed-off-by: Alejandro Hernandez <alejandro.hernandez@linux.intel.com>
Signed-off-by: Richard Purdie <richard.purdie@linuxfoundation.org>
|
|
Using a copy would only make management of devices erroneous
and makes the system unstable in some scenarios as tools will
have to manipulate both files separately. A link ensures that
both files /proc/mounts and /etc/mtab will have the same
information at all times and this is how it is handled
on newer systems where there is such a need. Same is
suggested by busybox.
Signed-off-by: Awais Belal <awais_belal@mentor.com>
Signed-off-by: Ross Burton <ross.burton@intel.com>
|
|
Some eMMC devices show special sub-devices such as mmcblk0boot0
etc. The installation script currently pick all of them up and
displays it to the user which makes some confusions because these
sub-devices are pretty small and complete installation including
rootfs won't be possible in most cases.
We simply now drop these sub-devices and only present the user
with the root of such mmc devices.
Signed-off-by: Awais Belal <awais_belal@mentor.com>
Signed-off-by: Ross Burton <ross.burton@intel.com>
|
|
It can take a bit for USB devices to be detected, so if a USB device is
your rootfs and you don't set rootwait you will most likely get a kernel
panic. Fix this by adding rootwait to the kernel command line on
installation.
Fixes [YOCTO #9462].
Signed-off-by: California Sullivan <california.l.sullivan@intel.com>
Signed-off-by: Ross Burton <ross.burton@intel.com>
|
|
booting
When live booting, we need to make sure the running udev processes are killed
to avoid unexepected behavior, we do this just before switching root,
once we do, a new udev process will be spawned from init and will take care
of whatever work was still missing
[YOCTO #9520]
Signed-off-by: Alejandro Hernandez <alejandro.hernandez@linux.intel.com>
Signed-off-by: Ross Burton <ross.burton@intel.com>
|
|
Its not immediately apparent that more than one install target could be
available. With this change we list the available devices up front then
prompt the user for which one to use, reducing confusion.
Fixes [YOCTO #9919].
Signed-off-by: California Sullivan <california.l.sullivan@intel.com>
Signed-off-by: Ross Burton <ross.burton@intel.com>
Signed-off-by: Richard Purdie <richard.purdie@linuxfoundation.org>
|
|
There might be more than one root=/dev/foo in the config file which
would cause unepected errros on the installed target, so remove all of
them.
[YOCTO #9354]
Signed-off-by: Robert Yang <liezhi.yang@windriver.com>
Signed-off-by: Richard Purdie <richard.purdie@linuxfoundation.org>
|
|
It mis-matched "SanDisk" or "Disk Flags" before, which caused unexpected
error.
Signed-off-by: Robert Yang <liezhi.yang@windriver.com>
Signed-off-by: Richard Purdie <richard.purdie@linuxfoundation.org>
|
|
* The name changes from overlayfs to overlayo
* The workdir is a must when mount
* The updir must be a subdir of rootfs.rw
This patch plus with another one which has been sent to linux-yocto can
fix the error when boot iso:
EXT4-fs (loop0): re-mounted. Opts: data=ordered
Populating dev cache
/etc/init.d/rc: /etc/rcS.d/S37populate-volatile.sh: line 1: can't create
/etc/volatile.cache.build: Read-only file system
/etc/rcS.d/S36udev-cache: line 73: can't create /etc/udev-cache.tar.gz:
Read-only file system
udev-cache: update failed!
rm: can't remove '/etc/udev/cache.data': Read-only file system
/etc/init.d/rc: /etc/rcS.d/S37populate-volatile.sh: line 1: can't create
/etc/volatile.cache.build: Read-only file system
/etc/init.d/rc: /etc/rcS.d/S37populate-volatile.sh: line 1: can't create
/etc/volatile.cache.build: Read-only file system
/etc/init.d/rc: /etc/rcS.d/S37populate-volatile.sh: line 1: can't create
/etc/volatile.cache.build: Read-only file system
/etc/init.d/rc: /etc/rcS.d/S37populate-volatile.sh: line 1: can't create
/etc/volatile.cache.build: Read-only file system
/etc/init.d/rc: /etc/rcS.d/S37populate-volatile.sh: line 1: can't create
/etc/volatile.cache.build: Read-only file system
/etc/init.d/rc: /etc/rcS.d/S37populate-volatile.sh: line 1: can't create
/etc/volatile.cache.build: Read-only file system
/etc/init.d/rc: /etc/rcS.d/S37populate-volatile.sh: line 1: can't create
/etc/volatile.cache.build: Read-only file system
/etc/init.d/rc: /etc/rcS.d/S37populate-volatile.sh: line 1: can't create
/etc/volatile.cache.build: Read-only file system
rm: can't remove '/tmp': Read-only file system
ln: /tmp/tmp: Read-only file system
/etc/init.d/rc: /etc/rcS.d/S37populate-volatile.sh: line 1: can't create
/etc/volatile.cache.build: Read-only file system
/etc/init.d/rc: /etc/rcS.d/S37populate-volatile.sh: line 1: can't create
/etc/volatile.cache.build: Read-only file system
/etc/init.d/rc: /etc/rcS.d/S37populate-volatile.sh: line 1: can't create
/etc/volatile.cache.build: Read-only file system
ln: /etc/resolv.conf: Read-only file system
/etc/init.d/rc: /etc/rcS.d/S37populate-volatile.sh: line 1: can't create
/etc/volatile.cache.build: Read-only file system
/etc/init.d/rc: /etc/rcS.d/S37populate-volatile.sh: line 1: can't create
/etc/volatile.cache.build: Read-only file system
Signed-off-by: Robert Yang <liezhi.yang@windriver.com>
Signed-off-by: Richard Purdie <richard.purdie@linuxfoundation.org>
|
|
The '/' in the end is not needed, which caused '//' in the path.
Signed-off-by: Robert Yang <liezhi.yang@windriver.com>
Signed-off-by: Richard Purdie <richard.purdie@linuxfoundation.org>
|
|
When booting from the live image, the label from the bootloader is passed
to init.sh. init.sh uses the label to either boot a live image or call a
script to take over and install the system.
It is possible to add new labels to the bootloader via the LABELS family of
variables, but the names in init.sh were hardcoded to install and
install-efi
this patch checks if a shell script with the same name as the label is
available instead of using a hardcoded list. Any recipe can add such file
and this provide a new boot target to the live image
Signed-off-by: Jérémy Rosen <jeremy.rosen@openwide.fr>
Signed-off-by: Ross Burton <ross.burton@intel.com>
|
|
Installing from USB to an internal SD Card did not work with Linux 4.4 in Yocto jethro. With this patch, consistent names are used for the paritions.
Signed-off-by: Urs Fässler <urs.fassler@bbv.ch>
Signed-off-by: Ross Burton <ross.burton@intel.com>
|
|
Running the install option from bootloader to install image to eMMC will fail
with error:
Formatting /dev/mmcblk01 to vfat...
mkfs.fat 3.0.28 (2015-05-16)
/dev/mmcblk01: No such file or directory
This issue impacts both grub and gummiboot install option to eMMC device.
The installation failure is due to the following:
[1] Unable to partition eMMC as the partition prefix 'p' is not appended
The condition checking failed with the additional /dev/ appended with
the target device name.
[2] The partition uuid for boot, root and swap partition is not captured
for eMMC
This fix updated the condition checking and changed the variables to
reference the boot, root and swap partitions for UUID.
[YOCTO #8710]
Signed-off-by: Ng, Mei Yeen <mei.yeen.ng@intel.com>
Signed-off-by: Ross Burton <ross.burton@intel.com>
|
|
After running gummiboot loader install option, the installed target
storage device boot parameter for root=PARTUUID is empty causing boot failure.
This issue is only observed with gummiboot and not with GRUB loader.
This fix assign the rootuuid of the rootfs partition for gummiboot loader.
[YOCTO #8709]
Signed-off-by: Ng, Mei Yeen <mei.yeen.ng@intel.com>
Signed-off-by: Ross Burton <ross.burton@intel.com>
|
|
The base-files recipe installs /mnt/mtab (it is a softlink of /proc/mounts),
so if an image includes the latter, there is no new to created it again inside
the install-efi.sh script, otherwise an error may occur as indicated on the
bug's site.
[YOCTO #7971]
Signed-off-by: Leonardo Sandoval <leonardo.sandoval.gonzalez@linux.intel.com>
Signed-off-by: Richard Purdie <richard.purdie@linuxfoundation.org>
|
|
In case there is no installation device present, give a better
message to the user and abort installation.
[YOCTO #7971]
Signed-off-by: Leonardo Sandoval <leonardo.sandoval.gonzalez@linux.intel.com>
Signed-off-by: Richard Purdie <richard.purdie@linuxfoundation.org>
|
|
Platforms which have the capability of using the MMC as an
installer medium will present the same MMC device as an
installation candidate. This happens because the MMC
devices appear as mmcblk<X> and the current script strips
up the <X> which is needed to identify an MMC device
uniqely.
This patch now updates the way device identifier stripping
is done and handles the exclusion of installer device from
installation candidates more generically.
Signed-off-by: Awais Belal <awais_belal@mentor.com>
Signed-off-by: Ross Burton <ross.burton@intel.com>
|
|
Fixed deletion of the partition table by increasing
amount of sectors from 2(correct for msdos PT) to 35 as
GPT size is 34 sectors + 1 sector for protective MBR.
Signed-off-by: Ed Bartosh <ed.bartosh@linux.intel.com>
|
|
Shortened code by including /dev/ prefix into variable.
Signed-off-by: Ed Bartosh <ed.bartosh@linux.intel.com>
|
|
Cleaned up spaces from init-install* shell scripts.
Signed-off-by: Ed Bartosh <ed.bartosh@linux.intel.com>
|
|
parted allows to use names for partitions if GPT partition table
is used on the device. msdos partitioning can have only partition
types: 'primary', 'logical' or 'extended'.
Used meaningful partition names in parted command line for GPT
partitioning.
Signed-off-by: Ed Bartosh <ed.bartosh@linux.intel.com>
|
|
Explicitly specified filesystem type for parted mkpart command.
This makes partition table to look more informative.
Signed-off-by: Ed Bartosh <ed.bartosh@linux.intel.com>
|
|
Used partition UUID in kernel command line to specify root partition.
Searched root device by file system uuid in GRUB configuration.
Used partition UUID in /etc/fstab to specify swap partition.
Used filesystem UUID in /etc/fstab to specify boot partition.
[YOCTO #6101]
Signed-off-by: Ed Bartosh <ed.bartosh@linux.intel.com>
|
|
Changed partition type from 'msdos' to 'gpt'.
Added special partition for grub stage2 bootloader.
NOTE: This is done only for GRUB 2 as legacy GRUB is
rarely used and doesn't support GPT partitions.
Signed-off-by: Ed Bartosh <ed.bartosh@linux.intel.com>
|
|
Using UUID in favor of device names is more reliable as
UUID names are persistent.
Device names can change as the order of adding device nodes
is arbitrary. This sometimes results in device names switching
on each boot, which can cause system fail to boot.
Persistent naming solves these issues.
Used partition UUID in kernel command line to specify root partition.
Used partition UUID in /etc/fstab to specify swap partition.
Used filesystem UUID in /etc/fstab to specify boot partition.
[YOCTO #6101]
Signed-off-by: Ed Bartosh <ed.bartosh@linux.intel.com>
|
|
The init script that invokes install and install-efi scripts
passes the first parameter that identifies the boot drive but
in cases when this disk is labeled and kernel configurations
allow disk labeling under /run/media/ this would pass the disk
label.
The earlier implementation considered that the drive name will
be passed and in case the label is passed it fails and provides
the boot drive as an option for installation driver.
We now use a more generic approach to identify the boot drive
which can handle both drive name as well as label if passed.
Signed-off-by: Awais Belal <awais_belal@mentor.com>
Signed-off-by: Ross Burton <ross.burton@intel.com>
|
|
After selecting the "install" gummiboot option of a Live image we are
seeing boot failure resulting from the gummiboot entries not being
installed correctly. This seems to be a problem in this init-install-efi.sh
script where it incorrectly installs the gummiboot entries into the root
filesystem, not the boot partition. We fix it by installing the entries in
the boot partition.
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Acked-by: Darren Hart <dvhart@linux.intel.com>
Signed-off-by: Richard Purdie <richard.purdie@linuxfoundation.org>
|
|
Signed-off-by: Drew Moseley <drew_moseley@mentor.com>
Signed-off-by: Saul Wold <sgw@linux.intel.com>
|
|
This is needed in case the boot disk was created with mkdiskimage.
In that case the parameter passed is a variant of /dev/sda4 which
includes the partition number. Without this change this install script
will offer to install onto the live media.
Signed-off-by: Drew Moseley <drew_moseley@mentor.com>
Signed-off-by: Saul Wold <sgw@linux.intel.com>
|
|
Some mmc cards do not have all the data files in /sys/block
populated. Check for existence before displaying the files
to avoid erroring out of the install process.
Signed-off-by: Drew Moseley <drew_moseley@mentor.com>
Signed-off-by: Saul Wold <sgw@linux.intel.com>
|
|
There are cases where software after boot may need to know the
current boot disk. Under the current system, it is not guaranteed
which disk is the boot. While /media/sda is a good guess, it
isn't always right, nor is it a good assumption that only one boot
disk is in the system. This gives a standard path to the original
boot disk mount which can be used to, for instance, update the
syslinux file on the boot media with a newer kernel, or updating
the boot parameters to add user options for future boots. Knowing
which disk is the boot media keeps from updating the non-boot
disk when for instance multiple syslinux boot medias are plugged in
(ie ensure correct syslinux is updated when the booted system is
updated).
Signed-off-by: Brian Lloyd <blloyd@familyhonor.net>
Signed-off-by: Saul Wold <sgw@linux.intel.com>
|
|
(This patch was originally done against init-install.sh in
OE-Core rev 358f0584d779825307eec08c023b5ff14e72cf9e)
Previously, only unremovable hard drives are searched and are treated
as candidates of target disks to intall into.
However, it's possible that we're going to install the live image into
a removable media such as an USB. This patch enables this possibility.
In addition, this patch presents more information about the hard drives
so that user may have more knowledge about which hard drive they are
going to install their image into.
Signed-off-by: Drew Moseley <drew_moseley@mentor.com>
Signed-off-by: Saul Wold <sgw@linux.intel.com>
|
|
(This patch was originally done against init-install.sh in
OE-Core rev aa67b1333b4774e1845f562085f7048df65a644f)
Previously, the boot partition was created for the target hard drive
but there was no corresponding entry for it in /etc/fstab. Besides,
even if the boot partition was mounted, it would just result in odd
directory hierarchy like /boot/boot/grub. However, what we really need
is /boot/grub. This patch fixes this problem.
Besides, for future maintance work, this patch also renames some of the
intermediate directories. It uses more descriptive names like /tgt_root
and /src_root. The name of /ssd is dropped.
Signed-off-by: Drew Moseley <drew_moseley@mentor.com>
Signed-off-by: Saul Wold <sgw@linux.intel.com>
|
|
Some mmc cards do not have all the data files in /sys/block
populated. Check for existence before displaying the files
to avoid erroring out of the install process.
Signed-off-by: Drew Moseley <drew_moseley@mentor.com>
Signed-off-by: Saul Wold <sgw@linux.intel.com>
|
|
Add a hotkey for the GRUB 'test' menuentry. This can be used by expect scripts to boot into 'test' when doing runtime hardware tests.
Signed-off-by: Corneliu Stoicescu <corneliux.stoicescu@intel.com>
Signed-off-by: Richard Purdie <richard.purdie@linuxfoundation.org>
|
|
The init-live.sh scripts assumes that the boot label set by
the LABELS variable is either "boot", "install", or
"install-efi". If that variable is overridden to something else
we fall off the end of the case statement and the system locks
up. If the boot label is unknown, at least attempt to boot.
Signed-off-by: Drew Moseley <drew_moseley@mentor.com>
Signed-off-by: Richard Purdie <richard.purdie@linuxfoundation.org>
|
|
Also small cosmetic changes.
Signed-off-by: Cristian Iorga <cristian.iorga@intel.com>
Signed-off-by: Richard Purdie <richard.purdie@linuxfoundation.org>
|
|
_EOF marker was not used properly
(space left before end of line).
Signed-off-by: Cristian Iorga <cristian.iorga@intel.com>
Signed-off-by: Richard Purdie <richard.purdie@linuxfoundation.org>
|
|
already exist
Overwriting of /etc/mtab would fail as below if the /etc/mtab link already
exist during installation phase, this patch fix this problem by checking
existance of the link before try to overwrite it.
Error message during installation if the /etc/mtab exists:
"cat: /proc/mounts: input file is output file"
Signed-off-by: Cristian Iorga <cristian.iorga@intel.com>
Signed-off-by: Richard Purdie <richard.purdie@linuxfoundation.org>
|
|
For automated hardware testing, boot process control
via serial interface is needed. As such, in grub, serial
line support is added upon testmaster image install.
Also add a specific timeout to automatically start
the master image upon start of testing phase.
Tested on multiple hardware targets without issues.
Signed-off-by: Cristian Iorga <cristian.iorga@intel.com>
Signed-off-by: Richard Purdie <richard.purdie@linuxfoundation.org>
|
|
Overwriting of /etc/mtab would fail as below if the /etc/mtab link already
exist during installation phase, this patch fix this problem by checking
existance of the link before try to overwrite it.
Error message during installation if the /etc/mtab exists:
"cat: /proc/mounts: input file is output file
Signed-off-by: Shan Hai <shan.hai@windriver.com>
Signed-off-by: Saul Wold <sgw@linux.intel.com>
|
|
We have this in recipes-bsp/grub/grub/40_custom:
[snip]
menuentry "Linux" {
set root=(hd0,1)
linux /vmlinuz root=__ROOTFS__ rw __CONSOLE__ __VIDEO_MODE__ __VGA_MODE__ quiet
}
[snip]
These lines are only for initrdscripts/files/init-install.sh, the side
effect is that it would make the target's grub-mkconfig doesn't work
well since the 40_custom will be installed to /etc/grub.d/40_custom, the
grub-mkconfig will run the 40_custom, and there will always be a
'menuentry "Linux"' menu in grub.cfg no matter it is valid or not, we
can do this in init-install.sh rather than grub to fix the problem,
which is also much simpler.
We have done the related work in init-install.sh, now we need remove our own
40_custom, and use grub's own 40_custom which is the right one.
Signed-off-by: Robert Yang <liezhi.yang@windriver.com>
Signed-off-by: Roy Li <rongqing.li@windriver.com>
Signed-off-by: Richard Purdie <richard.purdie@linuxfoundation.org>
|
|
We have this in recipes-bsp/grub/grub/40_custom:
[snip]
menuentry "Linux" {
set root=(hd0,1)
linux /vmlinuz root=__ROOTFS__ rw __CONSOLE__ __VIDEO_MODE__ __VGA_MODE__ quiet
}
[snip]
These lines are only for initrdscripts/files/init-install.sh, the side
effect is that it would make the target's grub-mkconfig doesn't work
well since the 40_custom will be installed to /etc/grub.d/40_custom, the
grub-mkconfig will run the 40_custom, and there will always be a
'menuentry "Linux"' menu in grub.cfg no matter it is valid or not, we
can do this in init-install.sh rather than grub to fix the problem,
which is also much simpler.
Signed-off-by: Robert Yang <liezhi.yang@windriver.com>
Signed-off-by: Saul Wold <sgw@linux.intel.com>
|
|
mount.sh in udev-extraconf was modified to use /run/media instead
of /media. Unfortunately, our scripts in initrdscripts have some
dependency on the auto-mounting mechanism proviced by udev-extraconf.
So these scripts should also be fixed to use /run/media instead /media,
otherwise, our live image cannot work correctly.
Signed-off-by: Chen Qi <Qi.Chen@windriver.com>
Signed-off-by: Saul Wold <sgw@linux.intel.com>
Signed-off-by: Richard Purdie <richard.purdie@linuxfoundation.org>
|
|
Instead of using 'ls /dev/sd*' command to list block devices, we
should rather use 'cat /proc/partitions'.
Signed-off-by: Chen Qi <Qi.Chen@windriver.com>
Signed-off-by: Saul Wold <sgw@linux.intel.com>
Signed-off-by: Richard Purdie <richard.purdie@linuxfoundation.org>
|
|
These are meant to be used by a master image, for a simple
initial setup.
The install scripts are similar to the default ones, but:
- custom partitioning, replaces the swap partiton with a second root filesystem
- adds labels to the partitions
- preconfigures a boot loader entry for the second rootfs
Part of [YOCTO #5614]
Signed-off-by: Stefan Stanacar <stefanx.stanacar@intel.com>
Signed-off-by: Richard Purdie <richard.purdie@linuxfoundation.org>
|
|
Adds a gummiboot class similar to grub-efi class and makes the necessary
changes so it can be used for live/hddimg images as well.
One can set EFI_PROVIDER = "gummiboot" in local.conf to use gummiboot instead of grub-efi.
Gummiboot requires some kernel options that are not enabled by default, so one has to build
with KERNEL_FEATURES_append = " cfg/efi-ext".
The install scripts have been updated too, keeping the old behaviour around,
but accounting for the new boot loader config files (if they exist).
It can be argued that the installer and bootimg are a bit wierd and not necessarily correct,
but I wanted to have the exact same behviour with gummiboot.
With the default EFI_PROVIDER = "grub-efi" nothing changes, everthing should be just as before.
I've tested live boot, install and normal boot on:
- FRI2
- genericx86-64 on NUC
with:
EFI_PROVIDER = "gummiboot"
KERNEL_FEATURES_append = " cfg/efi-ext"
in local.conf.
Signed-off-by: Stefan Stanacar <stefanx.stanacar@intel.com>
Signed-off-by: Saul Wold <sgw@linux.intel.com>
Signed-off-by: Richard Purdie <richard.purdie@linuxfoundation.org>
|
Carlos Alberto Lopez Perez
Alejandro Hernandez
Joe Konno
Awais Belal
California Sullivan
Robert Yang
Jérémy Rosen
Urs Fässler
Ng, Mei Yeen
Leonardo Sandoval
Ed Bartosh
Reinette Chatre
Drew Moseley
Brian Lloyd
Corneliu Stoicescu
Cristian Iorga
Shan Hai
Roy Li
Chen Qi
Stefan Stanacar